-
Original price was: د.ج 1.100,00.د.ج 900,00Current price is: د.ج 900,00.
It works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project. -
Original price was: د.ج 1.100,00.د.ج 900,00Current price is: د.ج 900,00.
It works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project. -
د.ج 150,00
- Length: 100 mm
- Weight: 30~35 gm each
- 1p-1p pin header
- Compatible with 2.54mm spacing pin headers
- 10pcs chromatic color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Be used for the electronic project and Genuine Arduino product
- Flexible Breadboard Jumper Cable Wire allows you plug and unplug easily for prototyping.
- Breadboard connections which allow you plug and unplug easily for prototyping and can be used over and over again.
-
د.ج 850,00 – د.ج 1.200,00
- 16 characters wide, 2 rows
- Blue/Green Backlight
- 5×7 Dot Matrix Character + Cursor
- HD44780 Equivalent LCD Controller/driver Built-In
- 4-bit or 8-bit MPU Interface
- Works with almost any Microcontroller
- Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used)
-
Original price was: د.ج 1.700,00.د.ج 1.500,00Current price is: د.ج 1.500,00.
- The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
-
د.ج 250,00
- Length: 200 mm
- Weight: 30~35 gm each
- 1p-1p pin header
- Compatible with 2.54mm spacing pin headers
- 10pcs chromatic color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Be used for the electronic project and Genuine Arduino product
- Flexible Breadboard Jumper Cable Wire allows you plug and unplug easily for prototyping.
- Breadboard connections which allow you plug and unplug easily for prototyping and can be used over and over again.
-
د.ج 2.000,00
- Supply voltage: 5V
- View angle: 6 O’clock
- Display type: positive / negative type
- Operating temperature: -20°C – +70°C
- Storage temperature: -30°C – 80°C
- Size: approx. 9.8cm x 6cm x 1.2cm
-
د.ج 2.200,00 – د.ج 3.000,00
- The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
- This shield allows you to control upto 4 stepper motors
- Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
- Arduino compatible
-
Original price was: د.ج 1.800,00.د.ج 1.600,00Current price is: د.ج 1.600,00.
-
Standard For Shield interfaces and shape
-
Can continue to stack other For expansion boards
-
3 M3 screw positioning holes for easy installation
-
High Drive (5V or 3.3V) normally open contact closure
-
Onboard relay indicator (red)
-
-
د.ج 120,00
- 5v Active Buzzer Magnetic Long Continous Beep Tone 12*9.5mm
-
Original price was: د.ج 850,00.د.ج 750,00Current price is: د.ج 750,00.
- Mini Submersible Pump Water Mute Water Pump For Arduino Uno
-
د.ج 450,00 – د.ج 1.750,00
- Equipped with high-current relay, AC250V 10A ; DC30V 10A
- Indication LEDs for Relay output status
- Equipped with screw holes for easy installation
- 5V 1/2/4/6/8 Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A ; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED s for Relay output status.
-
Original price was: د.ج 750,00.د.ج 600,00Current price is: د.ج 600,00.
- Simple step and direction control interface
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- Adjustable current control lets set the maximum current output with a potentiometer.
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
-
Original price was: د.ج 4.800,00.د.ج 3.200,00Current price is: د.ج 3.200,00.
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40°C to +85°C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
 |
