{[content_material]}
| Color | Blue, Green |
|---|
4.200,00 د.ج
- Very handy and simple in assembling/disassembling.
- Strong components so as to withstand extreme terrain conditions.
- Transparent Car Chassis.
- Attractive design.
- Double layer structure, much of mounting holes, enough space
2.400,00 د.ج
- Motor power supply is 3V~6V.
- All the parameter above is tested without load
- Please notice that the wooden outside is just a PROTECTION FILM. You need to TEAR OFF the yellow-brown protective paper outside the car chassis, and you will see the transparent clear car chassis inside.
- Please allow 1-2cm errors due to manual measurement
- Item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same
750,00 د.ج – 800,00 د.ج
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
900,00 د.ج
- It can run 2 servo or 2 stepper or 4 DC motor with the help of external power supply and controlling via arduino.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
1.200,00 د.ج
- Red LED checks the state of the proximity sensor
- High repeated positioning accuracy
- High switching frequency
- Wide voltage range
- Total Length of cylinder: 62mm.
- Thread length: 40mm.
- Outer (Theard) Diameter: M12
- Antivibration, dust, water and oil prevention
- Reverse power protection, short circuit protection, directly connecting with PLC
- Can replace small switches and limit switches
1.000,00 د.ج
- Stepper motor with a standard interface, when used directly pluggable.
- A, B, C, D four-phase LED indicator which indicates the status of the stepper motor work.
- Compact size stepper motor perfect for small robotics applications.
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
17.800,00 د.ج
- Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz
- 1GB LPDDR2 SDRAM
- 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE
- Gigabit Ethernet over USB 2.0 (maximum throughput of 300 Mbps)
- Extended 40-pin GPIO header
- Full-size HDMI
- 4 USB 2.0 ports
- CSI camera port for connecting a Raspberry Pi camera
- DSI display port for connecting a Raspberry Pi touchscreen display
- 4-pole stereo output and composite video port
- Micro SD port for loading your operating system and storing data
- 5V/2.5A DC power input
- Power-over-Ethernet (PoE) support (requires separate PoE HAT)
600,00 د.ج
- Digital Output
- Single Wire Output
- Stable & long term accuracy
- Full range temperature compensated
- Relative humidity and temperature measurement
- Calibrated digital signal
- Outstanding long-term stability
- pins packaged and fully interchangeable
- Low power consumption
- 4 pins package
850,00 د.ج
- Maximum motor supply voltage: 46V
- Maximum motor supply current: 2A per motor
- Current Sense for each motor
- Heat sink for better performance
- Power-On LED indicator
- Drives up to 4 motors.
1.500,00 د.ج
- The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
900,00 د.ج
- It can connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled a port with VCC, GND and Output, which has a corresponding port on the Sensor Shield.
- Make connections easier, secure and more professional looking.
- Sensor Shield V5.0 expansion moudle board for Arduino UNO R3.
- Including all I/O ports’ Pins for UNO R3 main board.
- With a Reset Button.
- Red LED indicates the power status, yellow LED indicates if connected to PIN 13
9.000,00 د.ج
- ATmega16U2 instead 8U2 as USB to serial converter
- 1.0 pinout
- Stronger RESET circuit
- 5V operating voltage
- Input voltage (recommended) range from 7V to 12V
- Input voltage (limit) range from 6V to 20V
- 40mA DC current per I/O pin
- 256KB flash memory of which 8KB used by bootloader
- 8KB SRAM
- 4KB EEPROM
600,00 د.ج
- Compatible with Arduino NANO
- All digital and analog pins breakout
- Compact size;
- Leads all pins out, convenient for wiring and doing experiments.
700,00 د.ج
- Compact size (24 x 32 mm)
- Infrared sensor: dual element, low noise, high sensitivity
- Light sensor: CdS photocell (can be add as customer requirement
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Blockade time: 2.5s (Default)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
Reviews
There are no reviews yet.