RASPBERRY PI SHIELDS
-
900,00 د.ج
It works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project. -
900,00 د.ج
It works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project. -
1.500,00 د.ج
Ideal for Android™ Smartphones and Tablets
SanDisk® cards are compatible with Android™ smartphones and tablets. -
150,00 د.ج
- Length: 100 mm
- Weight: 30~35 gm each
- 1p-1p pin header
- Compatible with 2.54mm spacing pin headers
- 10pcs chromatic color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Be used for the electronic project and Genuine Arduino product
- Flexible Breadboard Jumper Cable Wire allows you plug and unplug easily for prototyping.
- Breadboard connections which allow you plug and unplug easily for prototyping and can be used over and over again.
-
250,00 د.ج
- Length: 200 mm
- Weight: 30~35 gm each
- 1p-1p pin header
- Compatible with 2.54mm spacing pin headers
- 10pcs chromatic color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Be used for the electronic project and Genuine Arduino product
- Flexible Breadboard Jumper Cable Wire allows you plug and unplug easily for prototyping.
- Breadboard connections which allow you plug and unplug easily for prototyping and can be used over and over again.
-
450,00 د.ج
- Une carte adaptateur d’extension GPIO rouge(Ne comprend pas la planche à barbe 400 Points)Câble ruban plat 26 broches 2.54-picth 200mm
-
5.500,00 د.ج
- Designed for Raspberry Pi, an ideal alternative solution for HDMI monitor
- Supports all revision of Raspberry Pi (directly-pluggable models)
- Works with Raspbian/Ubuntu directly
- Comes with a full set of screws and nuts for assembly
- 320×480 resolution, better display
- Lightweight and easy to install
-
600,00 د.ج
- 30 x 30 x 10mm casing Frame size
- 25mm mounting hole spacing
- Cable Length 28 CM
- 4x 20mm Bolt and nuts are included
- Ready to plug Connector for Pi board
- Color: Black
-
1.600,00 د.ج
-
Standard For Shield interfaces and shape
-
Can continue to stack other For expansion boards
-
3 M3 screw positioning holes for easy installation
-
High Drive (5V or 3.3V) normally open contact closure
-
Onboard relay indicator (red)
-
-
120,00 د.ج
- 5v Active Buzzer Magnetic Long Continous Beep Tone 12*9.5mm
-
750,00 د.ج
- Mini Submersible Pump Water Mute Water Pump For Arduino Uno
-
450,00 د.ج – 1.750,00 د.ج
- Equipped with high-current relay, AC250V 10A ; DC30V 10A
- Indication LEDs for Relay output status
- Equipped with screw holes for easy installation
- 5V 1/2/4/6/8 Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A ; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED s for Relay output status.
-
1.200,00 د.ج
- 6-piece Acrylic case with access to all Ports on pi 4
- Compatible for All varient of the Raspberry pi 4 Model B
- Easy to assemble without any Screws or Nut-Bolts
- Slots to route GPIO and CSI ribbon cable
- Cut-out for micro SC card at the bottom panel
- Mounting holes and anti-slip rubber feet at the back.
-
1.100,00 د.ج
Ensures reliable, high-performance data transmission.
Gold plated connectors, strain relief and Mylar foil shielding Adapter constructed using high quality material for best connections
