1.100,00 د.ج900,00 د.جIt works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project.
1.100,00 د.ج900,00 د.جIt works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project.
60,00 د.ج- 10Pcs/Lot 3MM Ultra Bright Emitting Diode Dides Round Water Clear Green/Yellow/Blue/White/Red LED Light
120,00 د.ج- 5v Active Buzzer Magnetic Long Continous Beep Tone 12*9.5mm
4.800,00 د.ج3.200,00 د.ج- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40°C to +85°C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
10.000,00 د.ج9.000,00 د.جThe Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs,
4.200,00 د.ج3.200,00 د.ج- Robotics, DIY Kit and Projects that require High Speed Processing.
10.000,00 د.ج9.000,00 د.ج- ATmega16U2 instead 8U2 as USB to serial converter
- 1.0 pinout
- Stronger RESET circuit
- 5V operating voltage
- Input voltage (recommended) range from 7V to 12V
- Input voltage (limit) range from 6V to 20V
- 40mA DC current per I/O pin
- 256KB flash memory of which 8KB used by bootloader
- 8KB SRAM
- 4KB EEPROM
6.000,00 د.ج- ATmega16U2 instead 8U2 as USB to serial converter
- 1.0 pinout
- Stronger RESET circuit
- 5V operating voltage
- Input voltage (recommended) range from 7V to 12V
- Input voltage (limit) range from 6V to 20V
- 40mA DC current per I/O pin
- 256KB flash memory of which 8KB used by bootloader
- 8KB SRAM
- 4KB EEPROM
1.450,00 د.ج1.400,00 د.ج- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
4.200,00 د.ج3.500,00 د.ج- ATmega328 running at 16MHz with external resonator (0.5% tolerance)
- 0.8mm Thin PCB
- USB connection off board
- Supports auto-reset
- 5V regulator
- Max 150mA output
- Over-current protected
- Weighs less than 2 grams!
- DC input 5V up to 12V
- Onboard Power and Status LEDs
- Support serial download
6.500,00 د.ج- use the Arduino Software (IDE), and start tinker with coding and electronics.
5.000,00 د.ج4.200,00 د.ج- use the Arduino Software (IDE), and start tinker with coding and electronics.
2.900,00 د.ج2.700,00 د.ج- DIY project prototyping.
- Developing varied varieties of projects that require a code based control.
- Automation System development.
- Learning AVR programming.
- Entry level circuit designing.