1.100,00 د.ج900,00 د.جIt works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project.
1.100,00 د.ج900,00 د.جIt works without backlight, that is, in a dark environment OLED display is higher compared to that of LCD display you will like the miniature for its crispness.
The Driver chip of this OLED is SSD1306, which is compatible with IIC communication. So this module can be controlled by I2C.
That is, except the VCC and GND, 2 wires would be needed when using 4-wires I2C mode.
There is also a simple switch-cap charge pump that turns 5v into a low voltage drive for the OLEDs, making this module the easiest ways to get an OLED into your project.
5.000,00 د.ج3.700,00 د.ج- Popular RepRap 3D Printer LCD Controller and SD Card Reader Included adapter for RAMPS 1.4 board Fully supported by Marlin firmware With Smart LCD Controller you can print 3D designs without USB connection to your computer.
- LED background light control circuit
- This controller is 100% compatible with original design.
- LED background light control circuit, a small function of intelligent controller, With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do long or short form of the adjustment TRIM R4100K from 10 seconds to 2 minutes If you use a print job at night and parts department, which means that the new modifications LCD back light would be suitable for you.
850,00 د.ج – 1.200,00 د.ج- 16 characters wide, 2 rows
- Blue/Green Backlight
- 5×7 Dot Matrix Character + Cursor
- HD44780 Equivalent LCD Controller/driver Built-In
- 4-bit or 8-bit MPU Interface
- Works with almost any Microcontroller
- Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used)
1.700,00 د.ج1.500,00 د.ج- The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
2.000,00 د.ج- Supply voltage: 5V
- View angle: 6 O’clock
- Display type: positive / negative type
- Operating temperature: -20°C – +70°C
- Storage temperature: -30°C – 80°C
- Size: approx. 9.8cm x 6cm x 1.2cm
160,00 د.ج- Battery type: Zinc Carbon battery
- Dimension: 26.5mm x 48.5mm x 17.5mm
- Nominal voltage: 9V
- Cut-off voltage: 5.4V
- Discharge Resistance(Ω): 620
- Capacity : 600 mAh
4.000,00 د.ج3.500,00 د.ج- Using a large screen LCD 2004 4 lines of 20 characters per line Included adapter for RAMPS 1.4 board.
- After connecting this panel to your RAMPS 1.4 board, the smart controller supplies power to your SD card.
- The smart controller by the encoder creates all other operations, such as calibration or axis movement etc.
- 3D design print without a computer, just use the G code design stored on the SD card.
- Popular RepRap 3D Printer LCD Controller and SD Card Reader.
800,00 د.ج- Remote control switch, receiver module, motorcycles, automobile anti-theft products, home security products, electric doors, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote volume gate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm host, alarm, remote control motorcycle remote control electric cars, remote control MP3.