| Color | Blue, Green |
|---|
4.200,00 د.ج
- Very handy and simple in assembling/disassembling.
- Strong components so as to withstand extreme terrain conditions.
- Transparent Car Chassis.
- Attractive design.
- Double layer structure, much of mounting holes, enough space
2.400,00 د.ج
- Motor power supply is 3V~6V.
- All the parameter above is tested without load
- Please notice that the wooden outside is just a PROTECTION FILM. You need to TEAR OFF the yellow-brown protective paper outside the car chassis, and you will see the transparent clear car chassis inside.
- Please allow 1-2cm errors due to manual measurement
- Item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same
900,00 د.ج
- It can connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled a port with VCC, GND and Output, which has a corresponding port on the Sensor Shield.
- Make connections easier, secure and more professional looking.
- Sensor Shield V5.0 expansion moudle board for Arduino UNO R3.
- Including all I/O ports’ Pins for UNO R3 main board.
- With a Reset Button.
- Red LED indicates the power status, yellow LED indicates if connected to PIN 13
1.200,00 د.ج
- To measure and display temperature
- To Turn any application ON/OFF based on temperature reading . (Both AC and DC)
- Example Project :- A.Fire alarm system . B. Auto cut off Electric Water Heater
2.700,00 د.ج
- DIY project prototyping.
- Developing varied varieties of projects that require a code based control.
- Automation System development.
- Learning AVR programming.
- Entry level circuit designing.
1.200,00 د.ج
- Red LED checks the state of the proximity sensor
- High repeated positioning accuracy
- High switching frequency
- Wide voltage range
- Total Length of cylinder: 62mm.
- Thread length: 40mm.
- Outer (Theard) Diameter: M12
- Antivibration, dust, water and oil prevention
- Reverse power protection, short circuit protection, directly connecting with PLC
- Can replace small switches and limit switches
1.500,00 د.ج
Uses CH340G instead of CP2102.
- Wireless 802.11 b/g/n standard
- WiFi at 2.4GHz, support WPA / WPA2 security mode
- Support STA/AP/STA + AP three operating modes
- Built-in TCP/IP protocol stack to support multiple TCP Client connections (5 MAX)
- Support UART / GPIO data communication interface
- Remote firmware upgrade (OTA)
- Support Smart Link Smart Networking
- ESP8266 has IO Pin
- Don’t need to download resetting
- A great set of tools to develop ESP8266
- Lowest cost WI-FI
- FOR Arduino like hardware IO
- Greatly speed up your IOT application developing process
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- WI-FI MCU ESP8266 integrated and easy to prototyping development kit.
- We provide the best platform for IoT application development at the lowest cost.
- NodeMCU has built-in USB-TTL serial with super reliable industrial strength CH340G for superior stability on all supported platforms.
- Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.
- Event-driven API for network applications, which facilitates developers writing code running on a 5mm*5mm sized MCU in Nodejs style.
9.000,00 د.ج
- ATmega16U2 instead 8U2 as USB to serial converter
- 1.0 pinout
- Stronger RESET circuit
- 5V operating voltage
- Input voltage (recommended) range from 7V to 12V
- Input voltage (limit) range from 6V to 20V
- 40mA DC current per I/O pin
- 256KB flash memory of which 8KB used by bootloader
- 8KB SRAM
- 4KB EEPROM
750,00 د.ج – 800,00 د.ج
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
850,00 د.ج
- Maximum motor supply voltage: 46V
- Maximum motor supply current: 2A per motor
- Current Sense for each motor
- Heat sink for better performance
- Power-On LED indicator
- Drives up to 4 motors.
950,00 د.ج – 1.050,00 د.ج
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
3.200,00 د.ج
- Robotics, DIY Kit and Projects that require High Speed Processing.
800,00 د.ج
- Set of 3 aluminum heat sinks
- Suitable for Raspberry Pi B+, Pi 2 B, Pi 3B, Pi 4B. Preferably use with Raspberry Pi 4 Model B
- These heat sinks have profiles that are short enough to fit within standard Raspberry Pi cases.
- Material: aluminum
- Color: Black
3.200,00 د.ج
- The board is compatible with Mega 2560.
- excellent solution for developing projects based on ATmega2560.
- The board can be powered directly through the Micro USB connector
- The maximum output current upon 5V is around 800mA, while on the 3.3V it is about 800mA.
450,00 د.ج – 700,00 د.ج
- 100k Ohm NTC Thermistor.
- NTC Thin Film Thermistor Cable.
- Nominal value: R25 (25 ℃) : (common) 1.5K, 2K, 5K, 10K, 20K, 30K, 47K, 50K, 100K, 200K, 500K, etc.
- Resistance precision: ± 1%, ± 2%, ± 3%.
- B value R25/50 (common) 3435k, 3600k, 3950k, 3990k, 4100k, 4200k, etc.
- B value accuracy: ± 1%.
- Recommend the use of parameters: R25℃ = 100 k B25/50 = 3950 k ± 1%)
1.000,00 د.ج
- Stepper motor with a standard interface, when used directly pluggable.
- A, B, C, D four-phase LED indicator which indicates the status of the stepper motor work.
- Compact size stepper motor perfect for small robotics applications.
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
1.000,00 د.ج
- Integrated MF RC522
- 13.56MHz contactless communication card chip.
- Low-voltage, low-cost, small size of the non-contact card chip to read and write.
- Suitable for Smart meters and portable handheld devices.
- Advanced modulation and demodulation concept completely integrated in all types of 13.56MHz passive contactless communication methods and protocols.
- 14443A compatible transponder signals.
- ISO14443A frames and error detection.
- Supports rapid CRYPTO1 encryption algorithm, terminology validation MIFARE products.
- MFRC522 support MIFARE series of high-speed non-contact communication, two-way data transmission rate up to 424kbit/s.
- Low cost, and ideal for user equipment development.
- The reader and RF card terminal design meets advanced applications development and production needs.
- Can be directly loaded into the various reader molds, very convenient.
- Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
Reviews
There are no reviews yet.