Official website data download: http://www.orangepi.org/downloadresources/
250,00 د.ج
- Length: 200 mm
- Weight: 30~35 gm each
- 1p-1p pin header
- Compatible with 2.54mm spacing pin headers
- 10pcs chromatic color jump wire
- High quality and in good working condition
- Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Be used for the electronic project and Genuine Arduino product
- Flexible Breadboard Jumper Cable Wire allows you plug and unplug easily for prototyping.
- Breadboard connections which allow you plug and unplug easily for prototyping and can be used over and over again.
3.200,00 د.ج
- Robotics, DIY Kit and Projects that require High Speed Processing.
9.000,00 د.ج
- ATmega16U2 instead 8U2 as USB to serial converter
- 1.0 pinout
- Stronger RESET circuit
- 5V operating voltage
- Input voltage (recommended) range from 7V to 12V
- Input voltage (limit) range from 6V to 20V
- 40mA DC current per I/O pin
- 256KB flash memory of which 8KB used by bootloader
- 8KB SRAM
- 4KB EEPROM
1.500,00 د.ج
- The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
1.200,00 د.ج – 2.200,00 د.ج
- 64 or 128 K bytes of Flash memory
- 20 K bytes of SRAM
- 2.0 to 3.6 V application supply and I/Os
- 4-to-16 MHz crystal oscillator
- Internal 40 kHz RC
- 32 kHz oscillator for RTC with calibration
- 2 x 12-bit, 1μs A/D converters (up to 16 channels)
- 7-channel DMA controller
- Peripherals supported: timers, ADC, SPIs, I2Cs and USARTs
- Up to 2 x I2C interfaces (SMBus/PMBus)
- Up to 3 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)
- Up to 2 SPIs (18 Mbit/s)
- CAN interface (2.0B Active)
900,00 د.ج
- It can run 2 servo or 2 stepper or 4 DC motor with the help of external power supply and controlling via arduino.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
850,00 د.ج
- Maximum motor supply voltage: 46V
- Maximum motor supply current: 2A per motor
- Current Sense for each motor
- Heat sink for better performance
- Power-On LED indicator
- Drives up to 4 motors.
1.800,00 د.ج
- To measure and display temperature
- To Turn any application ON/OFF based on temperature reading . (Both AC and DC)
- Example Project :- A.Fire alarm system . B. Auto cut off Electric Water Heater
900,00 د.ج
- It can connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled a port with VCC, GND and Output, which has a corresponding port on the Sensor Shield.
- Make connections easier, secure and more professional looking.
- Sensor Shield V5.0 expansion moudle board for Arduino UNO R3.
- Including all I/O ports’ Pins for UNO R3 main board.
- With a Reset Button.
- Red LED indicates the power status, yellow LED indicates if connected to PIN 13
1.000,00 د.ج
- Integrated MF RC522
- 13.56MHz contactless communication card chip.
- Low-voltage, low-cost, small size of the non-contact card chip to read and write.
- Suitable for Smart meters and portable handheld devices.
- Advanced modulation and demodulation concept completely integrated in all types of 13.56MHz passive contactless communication methods and protocols.
- 14443A compatible transponder signals.
- ISO14443A frames and error detection.
- Supports rapid CRYPTO1 encryption algorithm, terminology validation MIFARE products.
- MFRC522 support MIFARE series of high-speed non-contact communication, two-way data transmission rate up to 424kbit/s.
- Low cost, and ideal for user equipment development.
- The reader and RF card terminal design meets advanced applications development and production needs.
- Can be directly loaded into the various reader molds, very convenient.
- Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
3.500,00 د.ج
- ATmega328 running at 16MHz with external resonator (0.5% tolerance)
- 0.8mm Thin PCB
- USB connection off board
- Supports auto-reset
- 5V regulator
- Max 150mA output
- Over-current protected
- Weighs less than 2 grams!
- DC input 5V up to 12V
- Onboard Power and Status LEDs
- Support serial download
Reviews
There are no reviews yet.