Type : LMK..LUU square flange long linear bearing series
Model number : LMK10LUU
Inside diameter : 10mm
Outer diameter : 19mm
Total length : 55mm
Package content :
Package Includes :
- 1 x pcs LMK10LUU
LMK10LUU long type 10mm flange linear bearing CNC Linear Bush
950,00 د.ج
- Outer Casing: Chromium Steel
- Low friction, optimum loading capacity, long life.
- It has linear bearing ball cage, hardened coat at both end rings.
- No worry if replacement of any worn part.
- Low noise even in high-speed operation.
| Sold Items | Hurry! only 2 left in stock |
| diametres | 8mm, 10mm, 12mm |
|---|
3.200,00 د.ج
- Supreme finish
- Smooth surface
- Long lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
1.200,00 د.ج
- The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
- This shield allows you to control upto 4 stepper motors
- Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
- Arduino compatible
7.500,00 د.ج – 11.000,00 د.ج
- vertical 500mm/1000mm Optical shaft linear guideway SC8UU/SC10UU/SC12UU Linear Ball Bearing Linear Rail Shaft Support SK8/SK10/SK12 for CNC 3D Printer
1.200,00 د.ج
- Red LED checks the state of the proximity sensor
- High repeated positioning accuracy
- High switching frequency
- Wide voltage range
- Total Length of cylinder: 62mm.
- Thread length: 40mm.
- Outer (Theard) Diameter: M12
- Antivibration, dust, water and oil prevention
- Reverse power protection, short circuit protection, directly connecting with PLC
- Can replace small switches and limit switches
500,00 د.ج
- Environmentally friendly materials, degradable.
- There are many styles and models, and there are different models for different needs.
6.000,00 د.ج
-
The product is divided into two sides of the A.B board.
-
A side:High temperature print layer B side:Low temperature adhesive layer
-
Separate bending to take the model. It is more convenient.
-
No need for beautiful paper and scrapers to assist the model.
-
Can be installed on hot bed and glass platform.
-
Printing does not warp. No glue is needed.
-
Can be printed on a cold bed.
4.000,00 د.ج
- Print the Widest Range of Materials Possible
- High-Temperature Performance
- High-Quality Printing
- Easy Mounting and Community Support
3.700,00 د.ج
- Popular RepRap 3D Printer LCD Controller and SD Card Reader Included adapter for RAMPS 1.4 board Fully supported by Marlin firmware With Smart LCD Controller you can print 3D designs without USB connection to your computer.
- LED background light control circuit
- This controller is 100% compatible with original design.
- LED background light control circuit, a small function of intelligent controller, With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do long or short form of the adjustment TRIM R4100K from 10 seconds to 2 minutes If you use a print job at night and parts department, which means that the new modifications LCD back light would be suitable for you.
550,00 د.ج – 850,00 د.ج
- Precision registration and timing with no loss of high torque carrying capability
- Minimal vibration and chordal effect Positive slip proof engagement
- Wide speed range, especially important when the entire speed range is developed from a single source
- Virtually no elongation (stretching) due to wear
- Power transmission efficiency is not lost with use
- Clean operation, no need for lubrication
- Reduced noise
- Long, dependable trouble-free service
75.000,00 د.ج
Anet A8 Plus 3D Printer Complete DIY With Max Printing Size 300*300*350mm
800,00 د.ج – 1.050,00 د.ج
-
SC8UU 8mm /SC10UU 10mm/SC12UU 12mm Linear Motion Ball Bearing Slide Block Unit for CNC 3D Printer is used on hardened steel shafts. This is ideal for small CNC applications. The universal Ball Bearings are easy to replace when it is damaged to improve the machine efficiency and save energy.
2.200,00 د.ج – 3.000,00 د.ج
- The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
- This shield allows you to control upto 4 stepper motors
- Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
- Arduino compatible
450,00 د.ج – 700,00 د.ج
- 100k Ohm NTC Thermistor.
- NTC Thin Film Thermistor Cable.
- Nominal value: R25 (25 ℃) : (common) 1.5K, 2K, 5K, 10K, 20K, 30K, 47K, 50K, 100K, 200K, 500K, etc.
- Resistance precision: ± 1%, ± 2%, ± 3%.
- B value R25/50 (common) 3435k, 3600k, 3950k, 3990k, 4100k, 4200k, etc.
- B value accuracy: ± 1%.
- Recommend the use of parameters: R25℃ = 100 k B25/50 = 3950 k ± 1%)
350,00 د.ج – 450,00 د.ج
- GT2 pulley with 20 teeth or grooves is one of the best choices for 3D printer construction. GT2 Timing Pulley 16 Tooth 5mm Bore for 6mm Belt can be used in all range of 3D Printers. It gives better smoothness and accuracy of positioning, resulting in better printing quality.
Reviews
There are no reviews yet.